sparrow-kit/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_hal_nand.c

/**
  ******************************************************************************
  * @file    stm32f1xx_hal_nand.c
  * @author  MCD Application Team
  * @brief   NAND HAL module driver.
  *          This file provides a generic firmware to drive NAND memories mounted 
  *          as external device.
  *         
  @verbatim
  ==============================================================================
                         ##### How to use this driver #####
  ==============================================================================    
    [..]
      This driver is a generic layered driver which contains a set of APIs used to 
      control NAND flash memories. It uses the FSMC layer functions to interface 
      with NAND devices. This driver is used as follows:
    
      (+) NAND flash memory configuration sequence using the function HAL_NAND_Init() 
          with control and timing parameters for both common and attribute spaces.
            
      (+) Read NAND flash memory maker and device IDs using the function
          HAL_NAND_Read_ID(). The read information is stored in the NAND_ID_TypeDef 
          structure declared by the function caller. 
        
      (+) Access NAND flash memory by read/write operations using the functions
          HAL_NAND_Read_Page_8b()/HAL_NAND_Read_SpareArea_8b(), 
          HAL_NAND_Write_Page_8b()/HAL_NAND_Write_SpareArea_8b(),
          HAL_NAND_Read_Page_16b()/HAL_NAND_Read_SpareArea_16b(), 
          HAL_NAND_Write_Page_16b()/HAL_NAND_Write_SpareArea_16b()
          to read/write page(s)/spare area(s). These functions use specific device 
          information (Block, page size..) predefined by the user in the NAND_DeviceConfigTypeDef 
          structure. The read/write address information is contained by the Nand_Address_Typedef
          structure passed as parameter.
        
      (+) Perform NAND flash Reset chip operation using the function HAL_NAND_Reset().
        
      (+) Perform NAND flash erase block operation using the function HAL_NAND_Erase_Block().
          The erase block address information is contained in the Nand_Address_Typedef 
          structure passed as parameter.
    
      (+) Read the NAND flash status operation using the function HAL_NAND_Read_Status().
        
      (+) You can also control the NAND device by calling the control APIs HAL_NAND_ECC_Enable()/
          HAL_NAND_ECC_Disable() to respectively enable/disable the ECC code correction
          feature or the function HAL_NAND_GetECC() to get the ECC correction code. 
       
      (+) You can monitor the NAND device HAL state by calling the function
          HAL_NAND_GetState()  

    [..]
      (@) This driver is a set of generic APIs which handle standard NAND flash operations.
          If a NAND flash device contains different operations and/or implementations, 
          it should be implemented separately.

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */ 

/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal.h"

/** @addtogroup STM32F1xx_HAL_Driver
  * @{
  */

#ifdef HAL_NAND_MODULE_ENABLED

#if defined (STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG) || defined(STM32F103xG)

/** @defgroup NAND NAND
  * @brief NAND HAL module driver
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @defgroup NAND_Private_Constants NAND Private Constants
  * @{
  */

/**
  * @}
  */

/* Private macro -------------------------------------------------------------*/    
/** @defgroup NAND_Private_Macros NAND Private Macros
  * @{
  */

/**
  * @}
  */

/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup NAND_Exported_Functions NAND Exported Functions
  * @{
  */
    
/** @defgroup NAND_Exported_Functions_Group1 Initialization and de-initialization functions 
  * @brief    Initialization and Configuration functions 
  *
  @verbatim    
  ==============================================================================
            ##### NAND Initialization and de-initialization functions #####
  ==============================================================================
  [..]  
    This section provides functions allowing to initialize/de-initialize
    the NAND memory
  
@endverbatim
  * @{
  */
    
/**
  * @brief  Perform NAND memory Initialization sequence
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  ComSpace_Timing: pointer to Common space timing structure
  * @param  AttSpace_Timing: pointer to Attribute space timing structure
  * @retval HAL status
  */
HAL_StatusTypeDef  HAL_NAND_Init(NAND_HandleTypeDef *hnand, FSMC_NAND_PCC_TimingTypeDef *ComSpace_Timing, FSMC_NAND_PCC_TimingTypeDef *AttSpace_Timing)
{
  /* Check the NAND handle state */
  if(hnand == NULL)
  {
     return HAL_ERROR;
  }

  if(hnand->State == HAL_NAND_STATE_RESET)
  {
    /* Allocate lock resource and initialize it */
    hnand->Lock = HAL_UNLOCKED;
    /* Initialize the low level hardware (MSP) */
    HAL_NAND_MspInit(hnand);
  } 

  /* Initialize NAND control Interface */
  FSMC_NAND_Init(hnand->Instance, &(hnand->Init));
  
  /* Initialize NAND common space timing Interface */  
  FSMC_NAND_CommonSpace_Timing_Init(hnand->Instance, ComSpace_Timing, hnand->Init.NandBank);
  
  /* Initialize NAND attribute space timing Interface */  
  FSMC_NAND_AttributeSpace_Timing_Init(hnand->Instance, AttSpace_Timing, hnand->Init.NandBank);
  
  /* Enable the NAND device */
  __FSMC_NAND_ENABLE(hnand->Instance, hnand->Init.NandBank);
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;

  return HAL_OK;
}

/**
  * @brief  Perform NAND memory De-Initialization sequence
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_DeInit(NAND_HandleTypeDef *hnand)  
{
  /* Initialize the low level hardware (MSP) */
  HAL_NAND_MspDeInit(hnand);

  /* Configure the NAND registers with their reset values */
  FSMC_NAND_DeInit(hnand->Instance, hnand->Init.NandBank);

  /* Reset the NAND controller state */
  hnand->State = HAL_NAND_STATE_RESET;

  /* Release Lock */
  __HAL_UNLOCK(hnand);

  return HAL_OK;
}

/**
  * @brief  NAND MSP Init
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval None
  */
__weak void HAL_NAND_MspInit(NAND_HandleTypeDef *hnand)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hnand);
  /* NOTE : This function Should not be modified, when the callback is needed,
            the HAL_NAND_MspInit could be implemented in the user file
   */ 
}

/**
  * @brief  NAND MSP DeInit
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval None
  */
__weak void HAL_NAND_MspDeInit(NAND_HandleTypeDef *hnand)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hnand);
  /* NOTE : This function Should not be modified, when the callback is needed,
            the HAL_NAND_MspDeInit could be implemented in the user file
   */ 
}


/**
  * @brief  This function handles NAND device interrupt request.
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval HAL status
*/
void HAL_NAND_IRQHandler(NAND_HandleTypeDef *hnand)
{
  /* Check NAND interrupt Rising edge flag */
  if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_RISING_EDGE))
  {
    /* NAND interrupt callback*/
    HAL_NAND_ITCallback(hnand);
  
    /* Clear NAND interrupt Rising edge pending bit */
    __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_RISING_EDGE);
  }
  
  /* Check NAND interrupt Level flag */
  if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_LEVEL))
  {
    /* NAND interrupt callback*/
    HAL_NAND_ITCallback(hnand);
  
    /* Clear NAND interrupt Level pending bit */
    __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_LEVEL);
  }

  /* Check NAND interrupt Falling edge flag */
  if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FALLING_EDGE))
  {
    /* NAND interrupt callback*/
    HAL_NAND_ITCallback(hnand);
  
    /* Clear NAND interrupt Falling edge pending bit */
    __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FALLING_EDGE);
  }
  
  /* Check NAND interrupt FIFO empty flag */
  if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FEMPT))
  {
    /* NAND interrupt callback*/
    HAL_NAND_ITCallback(hnand);
  
    /* Clear NAND interrupt FIFO empty pending bit */
    __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FEMPT);
  }
}

/**
  * @brief  NAND interrupt feature callback
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval None
  */
__weak void HAL_NAND_ITCallback(NAND_HandleTypeDef *hnand)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hnand);
  /* NOTE : This function Should not be modified, when the callback is needed,
            the HAL_NAND_ITCallback could be implemented in the user file
   */
}
 
/**
  * @}
  */
  
/** @defgroup NAND_Exported_Functions_Group2 Input and Output functions 
  * @brief    Input Output and memory control functions 
  *
  @verbatim    
  ==============================================================================
                    ##### NAND Input and Output functions #####
  ==============================================================================
  [..]  
    This section provides functions allowing to use and control the NAND 
    memory
  
@endverbatim
  * @{
  */

/**
  * @brief  Read the NAND memory electronic signature
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pNAND_ID: NAND ID structure
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Read_ID(NAND_HandleTypeDef *hnand, NAND_IDTypeDef *pNAND_ID)
{
  __IO uint32_t data = 0U;
  __IO uint32_t data1 = 0U;
  uint32_t deviceaddress = 0U;

  /* Process Locked */
  __HAL_LOCK(hnand);  
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* Send Read ID command sequence */   
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA))  = NAND_CMD_READID;
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;

  /* Read the electronic signature from NAND flash */
  if (hnand->Init.MemoryDataWidth == FSMC_NAND_PCC_MEM_BUS_WIDTH_8)
  {
    data = *(__IO uint32_t *)deviceaddress;

    /* Return the data read */
    pNAND_ID->Maker_Id   = ADDR_1ST_CYCLE(data);
    pNAND_ID->Device_Id  = ADDR_2ND_CYCLE(data);
    pNAND_ID->Third_Id   = ADDR_3RD_CYCLE(data);
    pNAND_ID->Fourth_Id  = ADDR_4TH_CYCLE(data);
  }
  else
  {
    data = *(__IO uint32_t *)deviceaddress;
    data1 = *((__IO uint32_t *)deviceaddress + 4U);
    
    /* Return the data read */
    pNAND_ID->Maker_Id   = ADDR_1ST_CYCLE(data);
    pNAND_ID->Device_Id  = ADDR_3RD_CYCLE(data);
    pNAND_ID->Third_Id   = ADDR_1ST_CYCLE(data1);
    pNAND_ID->Fourth_Id  = ADDR_3RD_CYCLE(data1);
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);
   
  return HAL_OK;
}

/**
  * @brief  NAND memory reset
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Reset(NAND_HandleTypeDef *hnand)
{
  uint32_t deviceaddress = 0U;

  /* Process Locked */
  __HAL_LOCK(hnand);

  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }

  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }  
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY; 
  
  /* Send NAND reset command */  
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = 0xFF;


  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);

  return HAL_OK;

}

/**
  * @brief  Configure the device: Enter the physical parameters of the device
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pDeviceConfig : pointer to NAND_DeviceConfigTypeDef structure
  * @retval HAL status
  */
HAL_StatusTypeDef  HAL_NAND_ConfigDevice(NAND_HandleTypeDef *hnand, NAND_DeviceConfigTypeDef *pDeviceConfig)
{
  hnand->Config.PageSize           = pDeviceConfig->PageSize;
  hnand->Config.SpareAreaSize      = pDeviceConfig->SpareAreaSize;
  hnand->Config.BlockSize          = pDeviceConfig->BlockSize;
  hnand->Config.BlockNbr           = pDeviceConfig->BlockNbr;
  hnand->Config.PlaneSize          = pDeviceConfig->PlaneSize;
  hnand->Config.PlaneNbr           = pDeviceConfig->PlaneNbr;
  hnand->Config.ExtraCommandEnable = pDeviceConfig->ExtraCommandEnable;
  
  return HAL_OK;
}
  
/**
  * @brief  Read Page(s) from NAND memory block (8-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to destination read buffer
  * @param  NumPageToRead : number of pages to read from block 
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Read_Page_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumPageToRead)
{   
  __IO uint32_t index  = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numPagesRead = 0U, nandaddress = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }

  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);

  /* Page(s) read loop */  
  while((NumPageToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = (hnand->Config.PageSize) + ((hnand->Config.PageSize) * numPagesRead);
    
    /* Send read page command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
   
    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }

    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA))  = NAND_CMD_AREA_TRUE1;
    
    /* Check if an extra command is needed for reading pages  */
    if(hnand->Config.ExtraCommandEnable == ENABLE)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
      
      /* Read status until NAND is ready */
      while(HAL_NAND_Read_Status(hnand) != NAND_READY)
      {
        if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
        {
          return HAL_TIMEOUT; 
        }
      }
      
      /* Go back to read mode */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
    }
    
    /* Get Data into Buffer */    
    for(; index < size; index++)
    {
      *(uint8_t *)pBuffer++ = *(uint8_t *)deviceaddress;
    }
    
    /* Increment read pages number */
    numPagesRead++;
    
    /* Decrement pages to read */
    NumPageToRead--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);

  return HAL_OK;
}

/**
  * @brief  Read Page(s) from NAND memory block (16-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to destination read buffer. pBuffer should be 16bits aligned
  * @param  NumPageToRead : number of pages to read from block 
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Read_Page_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumPageToRead)
{   
  __IO uint32_t index  = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numPagesRead = 0U, nandaddress = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }

  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);
  
  /* Page(s) read loop */  
  while((NumPageToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = (hnand->Config.PageSize) + ((hnand->Config.PageSize) * numPagesRead);
    
    /* Send read page command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;  
    
    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
  
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA))  = NAND_CMD_AREA_TRUE1;
    
    if(hnand->Config.ExtraCommandEnable == ENABLE)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
      
      /* Read status until NAND is ready */
      while(HAL_NAND_Read_Status(hnand) != NAND_READY)
      {
        if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
        {
          return HAL_TIMEOUT; 
        }
      }
      
      /* Go back to read mode */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
    }
    
    /* Get Data into Buffer */    
    for(; index < size; index++)
    {
      *(uint16_t *)pBuffer++ = *(uint16_t *)deviceaddress;
    }
    
    /* Increment read pages number */
    numPagesRead++;
    
    /* Decrement pages to read */
    NumPageToRead--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);  
    
  return HAL_OK;
}

/**
  * @brief  Write Page(s) to NAND memory block (8-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to source buffer to write  
  * @param  NumPageToWrite  : number of pages to write to block 
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_Page_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumPageToWrite)
{
  __IO uint32_t index = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numPagesWritten = 0U, nandaddress = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand);  

  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);
    
  /* Page(s) write loop */
  while((NumPageToWrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = hnand->Config.PageSize + ((hnand->Config.PageSize) * numPagesWritten);
    
    /* Send write page command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;

    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
  

    /* Write data to memory */
    for(; index < size; index++)
    {
      *(__IO uint8_t *)deviceaddress = *(uint8_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
    
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
      
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      }
    }
 
    /* Increment written pages number */
    numPagesWritten++;
    
    /* Decrement pages to write */
    NumPageToWrite--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);
  
  return HAL_OK;
}

/**
  * @brief  Write Page(s) to NAND memory block (16-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to source buffer to write. pBuffer should be 16bits aligned
  * @param  NumPageToWrite  : number of pages to write to block 
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_Page_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumPageToWrite)
{
  __IO uint32_t index = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numPagesWritten = 0U, nandaddress = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand);  

  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);
  
  /* Page(s) write loop */
  while((NumPageToWrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = (hnand->Config.PageSize) + ((hnand->Config.PageSize) * numPagesWritten);
 
    /* Send write page command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;

    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
  
    /* Write data to memory */
    for(; index < size; index++)
    {
      *(__IO uint16_t *)deviceaddress = *(uint16_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
    
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
    
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      } 
    }   
 
    /* Increment written pages number */
    numPagesWritten++;
    
    /* Decrement pages to write */
    NumPageToWrite--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }
  
  /* Update the NAND controller state */ 
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);
  
  return HAL_OK;
}

/**
  * @brief  Read Spare area(s) from NAND memory (8-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer: pointer to source buffer to write  
  * @param  NumSpareAreaToRead: Number of spare area to read  
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_NAND_Read_SpareArea_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaToRead)
{
  __IO uint32_t index = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numSpareAreaRead = 0U, nandaddress = 0U, columnaddress = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand);  
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);
  
  /* Column in page address */
  columnaddress = COLUMN_ADDRESS(hnand);
  
  /* Spare area(s) read loop */ 
  while((NumSpareAreaToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {     
    /* update the buffer size */
    size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaRead);

    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      /* Send read spare area command sequence */     
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
      
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      /* Send read spare area command sequence */ 
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
      
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }

    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;
    
    if(hnand->Config.ExtraCommandEnable == ENABLE)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
      
      /* Read status until NAND is ready */
      while(HAL_NAND_Read_Status(hnand) != NAND_READY)
      {
        if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
        {
          return HAL_TIMEOUT; 
        }
      }
      
      /* Go back to read mode */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
    }
    
    /* Get Data into Buffer */
    for(; index < size; index++)
    {
      *(uint8_t *)pBuffer++ = *(uint8_t *)deviceaddress;
    }
    
    /* Increment read spare areas number */
    numSpareAreaRead++;
    
    /* Decrement spare areas to read */
    NumSpareAreaToRead--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);

  return HAL_OK;
}

/**
  * @brief  Read Spare area(s) from NAND memory (16-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer: pointer to source buffer to write. pBuffer should be 16bits aligned.
  * @param  NumSpareAreaToRead: Number of spare area to read  
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_NAND_Read_SpareArea_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumSpareAreaToRead)
{
  __IO uint32_t index = 0U; 
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numSpareAreaRead = 0U, nandaddress = 0U, columnaddress = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand);
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);
  
  /* Column in page address */
  columnaddress = (uint32_t)(COLUMN_ADDRESS(hnand) * 2U);
  
  /* Spare area(s) read loop */ 
  while((NumSpareAreaToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaRead);

    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      /* Send read spare area command sequence */     
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
      
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      /* Send read spare area command sequence */     
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
      
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }

    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;

    if(hnand->Config.ExtraCommandEnable == ENABLE)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
      
      /* Read status until NAND is ready */
      while(HAL_NAND_Read_Status(hnand) != NAND_READY)
      {
        if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
        {
          return HAL_TIMEOUT; 
        }
      }
      
      /* Go back to read mode */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
    }
    
    /* Get Data into Buffer */
    for(; index < size; index++)
    {
      *(uint16_t *)pBuffer++ = *(uint16_t *)deviceaddress;
    }
    
    /* Increment read spare areas number */
    numSpareAreaRead++;
    
    /* Decrement spare areas to read */
    NumSpareAreaToRead--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);     

  return HAL_OK;  
}

/**
  * @brief  Write Spare area(s) to NAND memory (8-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to source buffer to write  
  * @param  NumSpareAreaTowrite  : number of spare areas to write to block
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_SpareArea_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaTowrite)
{
  __IO uint32_t index = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numSpareAreaWritten = 0U, nandaddress = 0U, columnaddress = 0U;

  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the FSMC_NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* Page address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand); 
  
  /* Column in page address */
  columnaddress = COLUMN_ADDRESS(hnand);
  
  /* Spare area(s) write loop */
  while((NumSpareAreaTowrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaWritten);

    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      /* Send write Spare area command sequence */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
      
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      /* Send write Spare area command sequence */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
    
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
  
    /* Write data to memory */
    for(; index < size; index++)
    {
      *(__IO uint8_t *)deviceaddress = *(uint8_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
    
    /* Get tick */
    tickstart = HAL_GetTick();
    
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      }
    }

    /* Increment written spare areas number */
    numSpareAreaWritten++;
    
    /* Decrement spare areas to write */
    NumSpareAreaTowrite--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }

  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;

  /* Process unlocked */
  __HAL_UNLOCK(hnand);
    
  return HAL_OK;
}

/**
  * @brief  Write Spare area(s) to NAND memory (16-bits addressing)
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to source buffer to write. pBuffer should be 16bits aligned.  
  * @param  NumSpareAreaTowrite  : number of spare areas to write to block
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_SpareArea_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumSpareAreaTowrite)
{
  __IO uint32_t index = 0U;
  uint32_t tickstart = 0U;
  uint32_t deviceaddress = 0U, size = 0U, numSpareAreaWritten = 0U, nandaddress = 0U, columnaddress = 0U;

  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the FSMC_NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* NAND raw address calculation */
  nandaddress = ARRAY_ADDRESS(pAddress, hnand);
  
  /* Column in page address */
  columnaddress = (uint32_t)(COLUMN_ADDRESS(hnand) * 2U);
  
  /* Spare area(s) write loop */
  while((NumSpareAreaTowrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
  {
    /* update the buffer size */
    size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaWritten);

    /* Cards with page size <= 512 bytes */
    if((hnand->Config.PageSize) <= 512U)
    {
      /* Send write Spare area command sequence */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
    
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
    else /* (hnand->Config.PageSize) > 512 */
    {
      /* Send write Spare area command sequence */
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
      *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
    
      if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
      }
      else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
      {
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
        *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
      }
    }
  
    /* Write data to memory */
    for(; index < size; index++)
    {
      *(__IO uint16_t *)deviceaddress = *(uint16_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
   
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      /* Get tick */
      tickstart = HAL_GetTick();
    
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      }
    }

    /* Increment written spare areas number */
    numSpareAreaWritten++;
    
    /* Decrement spare areas to write */
    NumSpareAreaTowrite--;
    
    /* Increment the NAND address */
    nandaddress = (uint32_t)(nandaddress + 1U);
  }

  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;

  /* Process unlocked */
  __HAL_UNLOCK(hnand);

  return HAL_OK;  
}

/**
  * @brief  NAND memory Block erase 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Erase_Block(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress)
{
  uint32_t deviceaddress = 0U;
  uint32_t tickstart = 0U;
  
  /* Process Locked */
  __HAL_LOCK(hnand);
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* Send Erase block command sequence */
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE0;

  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
    
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE1; 
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Get tick */
  tickstart = HAL_GetTick();
  
  /* Read status until NAND is ready */
  while(HAL_NAND_Read_Status(hnand) != NAND_READY)
  {
    if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
    {
      /* Process unlocked */
      __HAL_UNLOCK(hnand);    
  
      return HAL_TIMEOUT; 
    } 
  }    
 
  /* Process unlocked */
  __HAL_UNLOCK(hnand);    
  
  return HAL_OK;  
}

/**
  * @brief  NAND memory read status 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval NAND status
  */
uint32_t HAL_NAND_Read_Status(NAND_HandleTypeDef *hnand)
{
  uint32_t data = 0U;
  uint32_t deviceaddress = 0U;
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FSMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  } 

  /* Send Read status operation command */
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_STATUS;
  
  /* Read status register data */
  data = *(__IO uint8_t *)deviceaddress;

  /* Return the status */
  if((data & NAND_ERROR) == NAND_ERROR)
  {
    return NAND_ERROR;
  } 
  else if((data & NAND_READY) == NAND_READY)
  {
    return NAND_READY;
  }

  return NAND_BUSY; 
}

/**
  * @brief  Increment the NAND memory address
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param pAddress: pointer to NAND address structure
  * @retval The new status of the increment address operation. It can be:
  *           - NAND_VALID_ADDRESS: When the new address is valid address
  *           - NAND_INVALID_ADDRESS: When the new address is invalid address
  */
uint32_t HAL_NAND_Address_Inc(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress)
{
  uint32_t status = NAND_VALID_ADDRESS;
 
  /* Increment page address */
  pAddress->Page++;

  /* Check NAND address is valid */
  if(pAddress->Page == hnand->Config.BlockSize)
  {
    pAddress->Page = 0U;
    pAddress->Block++;
    
    if(pAddress->Block == hnand->Config.PlaneSize)
    {
      pAddress->Block = 0U;
      pAddress->Plane++;

      if(pAddress->Plane == (hnand->Config.PlaneNbr))
      {
        status = NAND_INVALID_ADDRESS;
      }
    }
  } 
  
  return (status);
}
/**
  * @}
  */

/** @defgroup NAND_Exported_Functions_Group3 Peripheral Control functions 
 *  @brief   management functions 
 *
@verbatim   
  ==============================================================================
                         ##### NAND Control functions #####
  ==============================================================================  
  [..]
    This subsection provides a set of functions allowing to control dynamically
    the NAND interface.

@endverbatim
  * @{
  */ 

    
/**
  * @brief  Enables dynamically NAND ECC feature.
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval HAL status
  */    
HAL_StatusTypeDef  HAL_NAND_ECC_Enable(NAND_HandleTypeDef *hnand)
{
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }

  /* Update the NAND state */
  hnand->State = HAL_NAND_STATE_BUSY;
   
  /* Enable ECC feature */
  FSMC_NAND_ECC_Enable(hnand->Instance, hnand->Init.NandBank);
  
  /* Update the NAND state */
  hnand->State = HAL_NAND_STATE_READY;
  
  return HAL_OK;
}

/**
  * @brief  Disables dynamically FSMC_NAND ECC feature.
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval HAL status
  */  
HAL_StatusTypeDef  HAL_NAND_ECC_Disable(NAND_HandleTypeDef *hnand)
{
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }

  /* Update the NAND state */
  hnand->State = HAL_NAND_STATE_BUSY;
    
  /* Disable ECC feature */
  FSMC_NAND_ECC_Disable(hnand->Instance, hnand->Init.NandBank);
  
  /* Update the NAND state */
  hnand->State = HAL_NAND_STATE_READY;
  
  return HAL_OK;  
}

/**
  * @brief  Disables dynamically NAND ECC feature.
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  ECCval: pointer to ECC value 
  * @param  Timeout: maximum timeout to wait    
  * @retval HAL status
  */
HAL_StatusTypeDef  HAL_NAND_GetECC(NAND_HandleTypeDef *hnand, uint32_t *ECCval, uint32_t Timeout)
{
  HAL_StatusTypeDef status = HAL_OK;
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Update the NAND state */
  hnand->State = HAL_NAND_STATE_BUSY;  
   
  /* Get NAND ECC value */
  status = FSMC_NAND_GetECC(hnand->Instance, ECCval, hnand->Init.NandBank, Timeout);
  
  /* Update the NAND state */
  hnand->State = HAL_NAND_STATE_READY;

  return status;  
}

/**
  * @}
  */
  
    
/** @defgroup NAND_Exported_Functions_Group4 Peripheral State functions 
 *  @brief   Peripheral State functions 
 *
@verbatim   
  ==============================================================================
                         ##### NAND State functions #####
  ==============================================================================  
  [..]
    This subsection permits to get in run-time the status of the NAND controller 
    and the data flow.

@endverbatim
  * @{
  */
  
/**
  * @brief  return the NAND state
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @retval HAL state
  */
HAL_NAND_StateTypeDef HAL_NAND_GetState(NAND_HandleTypeDef *hnand)
{
  return hnand->State;
}

/**
  * @}
  */  

/**
  * @}
  */

/**
  * @}
  */

#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG */
#endif /* HAL_NAND_MODULE_ENABLED  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/